Poster at ECIC: Assessement of an e-Learning program of FHR monitoring. A randomised study

A French study shows that training in CTG interpretation using an e-learning program improves the performance of obstetrical staff.  A poster of this study was presented at the European Congress on Intrapartum Care (ECIC) in Amsterdam this spring.
 

Read more

Newsletter September 2013

Latest news from NeoventaNewsletter September 2013
Subscribe to Neoventa Newsletter

Read more

M.Sc thesis from Chalmers University in Sweden explores diffusion of the STAN-method in the fetal monitoring industry.

In June 2013, two students from the M.Sc programme “Management and Economics of Innovation” at Chalmers University of Technology presented their M.Sc thesis focusing on the fetal monitoring industry and STAN in particular. Their research study analyzes diffusion of STAN in Europe and utilizes the most cutting-edge theory and research methods at hand within the discipline of industrial management on the conditions for diffusion. During the study over 25 interviews were conducted with clinical professionals in 4 European countries, investigating …

Read more

Meta-Analysis shows significant improvements with ST-analysis

The March 2013 American Journal of Obstetrics and Gynecology (AJOG) included a publication by Schuit et al. entitled “Effectiveness of electronic fetal monitoring with additional ST analysis in vertex singleton pregnancies at >36 weeks of gestation: an individual participant data meta-analysis (MA).” Since the publication of the AJOG article, there have been two Letters to Editor, one from Prof. Rosen and a response from the authors, regarding issues with this particular MA. We encourage you to read these letters (on-line) …

Read more

Renewed meta-analysis: Further support for ST Analysis

The objective of this meta-analysis was to investigate the additional effect of ST Analysis as an adjunct to electronic fetal monitoring. In order to overcome the shortcomings of conventional meta-analysis that uses aggregated data, the present analysis used individual participant data to allow for a more thorough investigation by taking all information into account, including accounting for missing data.
Only four of the five published randomised controlled trials (RCT) were included in the analysis. The first RCT by Westgate …

Read more

Newsletter December 2012

Lates news from NeoventaNewsletter December 2012

//

Subscribe to Neoventa Newsletter

Name

E-mail address

 

HTMLText

Newsletter Archive December 2012 July 2012 March 2012 October 2011
 

Read more

How to configure STAN S31 for automatic clock synchronization

There are two ways of synchronizing the STAN S31 system clock. You can either set up synchronization against a central monitoring system (CMS) that is connected via RS-232, and you can set up synchronization against a network server via TCP/IP.
To set up synchronization against a CMS, the following prerequisites must be fulfilled:A: Your STAN S31 must have software version R6A or later.B: You must a Central Monitoring System that support clock synchronization. (Check with your CMS vendor for confirmation.)
Read more

How to configure STAN S31 for IP networking

First connect the STAN to the network using a TP (i.e. twisted pair) network cable with RJ-45 connectors. Ensure that the correct cabling is used and that a CNK 101 003 Ethernet Isolation Box is connected between the STAN and the network. If you want to connect STAN directly to the network port of a printer, without going e.g. through a switch or a network HUB, the Rx/Tx signals of the cable need to be crossed.
Start the STAN and …

Read more

How to configure STAN for network printing

Ensure that the printer supports the PCL-5 language, that it has a network connection and supports the LPD (Line Printer Daemon) network protocol. Optionally, the printer can be connected through a network printer server that supports LPD.
Configure STAN for IP networking as described above. If STAN and the printer are to be connected locally using a crossed cable, we recommend that both STAN and printer are configured with fixed IP addresses in the 192.168.0.x series (e.g. 192.168.0.1 for STAN …

Read more

How to build a demo USB with your own STAN cases

Building your own demo USB to use with Stan S31, containing your own recordings is easy.
1. Use a USB stick that works with Stan S31. Note that you cannot use the same USB as you use for archiving Stan recordings.
2. To test whether a USB stick works with Stan, start a new recording, hold down the ‘End’ menu button and then press the ‘System Status’ dialog that appears. Select the ‘External devices’ view. Connect your USB stick to …

Read more
Page 7 of 11 «...56789...»

# #